Pupillary Distance and Heights Featured

Introduction To Dispensing – Pupillary Distance & Heights

Measuring the correct pupillary distance and pupil heights for your customers is quintessential to proper optical dispensing. Get it right and your customers will love their new glasses, get it wrong and they will promptly be back to return their glasses.

In this lesson, you will learn why are these measurements so important, as well as how they are used during the lens edging & mounting process.

Why Are Pupillary Distance and Pupil Height Measurements So Important?

To gain a deeper understanding let’s first review a few important points from previous lessons:

Here’s an example:

Light is focused on the retina - minus lens

In this example, we have a myopic eye. A minus lens diverges light slightly, then the cornea (a plus lens) converges the light to a focal point that is on the retina.

Side note: Compared to ray diagrams in The Optics of Vision course, you might think that I’ve drawn an absurdly large lens in this diagram. In actuality, this is much closer to the real-life proportions of the lenses we work with.

Picture showing the size of a lens blank compared to the eye

Now let’s focus in on the area of interest from the diagram above; the focal point forming on the retina.

Close up of light focusing on retina
Light comes to a focus precisely on the retina.

In reality, we don’t just want the focal point to be on the retina, we want it to be exactly on the macula.

What is the Macula?

The macula is a small red area on the retina that is able to produce very sharp vision. Click here for more information.

What is the Difference Between the Retina and the Macula?

The retina is the entire layer that lines the inside back portion of the eyes. Most of the retina cannot produce sharp vision.

The macula makes up a very small portion of the retina, but it is the only portion able to produce sharp vision.

Picture of the Macula

This image shows the macula. It appears as a small red spot inside the eyes. It is on that tiny little red spot that light must come to a focus for us to see clearly. The rest of the retina senses light, but does not produce sharp vision.

Important Take-Home:

The macula produces sharp vision, the rest of the retina does not.

Therefore:

Light must focus on the macula for vision to be clear. 

Here is how I will represent the macula in a cross-section diagram.

Close up of light focusing on the macula

How Do We Get The Focal Point Onto The Macula?

In order to properly position the focal point on the macula, we have to know:

  1. Where a lens’ focal point will be.
  2. Where the macula is.

Where Is The Focal Point?

A lens’s focal point is always in line with its optical center.

Here is a diagram that illustrates a plus lens creating a focal point. Notice that lens’s optical center and its focal point both lie on the same straight line (green).

Diagram illustrating the focal point is in line with the optical center of the lens

Where Is The Macula?

The macula is always in line with the center of the pupil.

Here is a cross section of an eye. Notice that the center of the pupil and the macula both lie on the same straight line (green).

Diagram illustrating that macula is in line with the center of the pupil

Combine It All Together

We now know that that focal point is in line with the lens’ optical center, and the macula is in line with the center of the pupil. Combining these two pieces of information tells us that aligning the lens’ optical center with the center of the pupil will place the focal point on the macula.

This is a diagram showing the optical center of the lens being lined up with the center of the pupil. As a result, the focal point falls exactly on the macula.

Diagram illustrating the focal point on the macula

This is a diagram showing what happens with the optical center of the lens is not lined up with the center of the pupil. As a result, the focal point does not form on the macula.

Diagram illustrating the focal point not on the macula

Main Take-Aways

For vision to be clear, the lens must focus light exactly on the macula.

For a lens to focus light exactly on the macula, the optical center of the lens must be aligned with the center of the pupil.

Note to all the seasoned dispensers reading this If you’re screaming ‘INDUCED PRISMATIC EFFECT‘ at the screen right now; cool it. This is a beginners course.

Now, let’s shift gears and talk about glasses.

How To Align the Optical Center of a Lens With The Center of the Pupil

Glasses frames do one thing; they hold the lenses in front of the eyes. But before the lenses are placed in the frames, they are just large discs called semi-finished lenses.

Semi-finished lenses have prescription in them, and coatings on them, but they are not yet cut to the shape of the glasses frame they will eventually be mounted into.

example of a semi-finished lens drawer full of semi-finished lenses
A semi-finished lens. A drawer full of semi-finished lenses in different prescriptions.

Semi-finished lenses typically have a diameter of 70mm. This is intentionally bigger than most glasses frames so that they can be cut down to fit any size/shape of frame.

Semi finished lens compared to glasses frames
The size of a semi-finished lens compared to glasses frames.

So if we’re starting with a lens that is way bigger than the glasses frame, here’s the problem: Which part of the lens are we going to put into the frame?

Just imagine that the semi-finished lens blank is a sheet of rolled out cookie dough and the shape of frame is the cookie cutter. We have to cut out a piece of the lens and put it in the frame. But which part of the semi-finished lens (cookie dough) are you going to cut out and use for the glasses?

Which Part of The Semi-Finsihed Lens Should Be Cut

Let’s remember what the goal is.

The goal is to align the optical center of the lens with the center of the pupil.

This means we’re going to need to know 2 things:

  1. Where the optical center of the lens is
  2. Where the center of the pupil is when the glasses are worn

Where is the Optical Center of a Semi-Finished Lens?

For now, you can assume that the optical center is in the exact middle of the semi-finished lens. This is not always the case, but for the purpose of this lesson we can assume that it is.

optical center of semi finished lens blank

Where is the center of the pupil when the glasses are worn?

Where the center of the pupil falls when glasses are worn will be different for every person and for every frame. Here is an example of me wearing a pair glasses:

a man wearing black glasses

Look at where the center of my pupils are on both the left and right sides. That is where the optical center of the lenses should be placed.

In order to place the optical center of the lenses exactly where my pupils are, we need two measurements:

  1. The pupillary distance
  2. The pupil height

The Pupillary Distance

The pupillary distance (PD) is the distance between the center of the two pupils, measured in millimeters (mm). It is a very useful measurement to take because for any given (adult) person, the PD never changes. This means that you only have to measure a person’s PD once, and it can used with any frame.

The image below shows that my pupillary distance is 60mm.

pupillar distance

 

Pupils Heights

The pupils height, often just called the height, is the distance from the center of the pupil to the frame’s bottom rim, measured in millimeters (mm). This measurement is frame specific, meaning that for any given person, wearing a different frame will result in a different height measurements.

The image below shows that my pupil height with this frame is 23mm.

pupil height

Why are Heights Frame Specific but the Pupillary Distance is Not?

You do not have to understand this, but if that’s what you’re wondering: I like where you’re head’s at. You should consider becoming an optician.

Once the pupillary distance and pupil heights have been measured, you have essentially established a set of coordinates. These coordinates will tell the edging lab exactly where and how to cut the semi-finished lenses in order for the optical center of the lenses to be perfectly aligned with the center of the pupils when the glasses are worn.

Measuring Pupillary Distance and Pupil Heights

There are many ways to measure both the pupillary distance and pupil heights. In order to properly explore all the relevant techniques, I will dedicate a separate lesson for this.

Let’s Do A Run Through

The customer has chosen a frame and wants to get his prescription put into them. We have a semi-finished lens blank with the customer’s prescription in it. What do we need to do in order to properly position the lens within the frame?

Remember: The goal is to position the lens’ optical center directly over top of the center of the customer’s pupil.

Customers Frame and Semi Finished Lens Blank

 

Step 1: Measure the customer’s PD (glasses off). This gives us the horizontal position for the lens.

Step 2: Measure the customer’s pupil height (glasses on). This gives us the vertical position for the lens.

We now have all the information to determine exactly where the center of pupils will be when the customer wears the glasses.

Customers Frame and Semi Finished Lens Blank With Eyes

This tells the edging lab exactly what part of the semi-finished lens to cut out and put into the frame to give the customer the best vision possible.

Semi Finished Lens Centered On Pupil

Summary

Making glasses is not as simple as just putting a lens into a frame. Many things have to be taken into careful consideration, including where the optical center of lens is in relation to the customer’s eyes.

Here is a summary of the key take-homes:

  • Every prescription lens has an optical center – the part of the lens that offers the best possible vision
  • The goal when making glasses is to align the lens’ optical center with the center of the customer’s pupil
  • To pinpoint where the center of the customer’s pupil will be when the glasses are worn, two measurements need to be taken – the pupillary distance and the pupil height

In the next lesson we will learn the techniques and instruments used to take these measurements.

 

 

The Crystalline Lens - Featured

The Optics of Vision – Part 9: The Crystalline Lens

If you thought the way the eye works was cool before, this is going to blow your mind. You’re about to learn about the crazy wonders of the the cyrstalline lens.

This lesson builds on all of the previous lessons in this course, so please make sure you are up to speed before tackling this one.

What is The Crystalline Lens?

This is the ray diagram of the eye that we are familiar with now.

Ray diagram of an emmetropic eye

The truth is that this diagram doesn’t actually show the complete picture of how the eye focuses light. This diagram depicts the cornea as being the only lens that focuses light for the eye. In fact, there are actually two structures that act as lenses. 

  1. The cornea
  2. The crystalline lens

Here is a diagram that depicts both the cornea and the crystalline lens. 

Ray Diagram of the eye with labelled cornea and crystalline lens

The crystalline lens is hidden just behind the iris. You cannot see it on your own as it is transparent and it is too dark in side the eyes to see.

What is the Power of the Crystalline Lens?

In past lessons, I have used +50D to represent the strength of the cornea.Ray Diagram of the eye with no crystalline lens

 

This is not actually the case. In reality, the total power of the eye is closer to +60D. The cornea is about +40D and the crystalline lens is approximately +20D (at rest… more on this a little later on). 

Here is a more accurate picture of the power of the eye. Keep in mind this is still a little simplified, but this is more than enough for you to know.

Power of the corean and crystalline lens

Review of Light Vergence & Distance

Before I reveal why the crystalline lens is so fascinating, we need to do a brief review of the vergence of light emitted from different distances. 

This would be a good time to review Lesson 1: Understanding Light

Here are the key points to remember:

  • Light that is emitted by objects is always divergent.
  • As the light travels away from the object it becomes less divergent.
  • Eventually, when the light has traveled more than 6 meters (20 feet), the light becomes parallel and stays that way.  

This diagram illustrates these key points:

ray diagram showing divergent light from object becoming parallel over a distance of 20ft

Have you noticed that whenever I have drawn a ray diagram of the eye, the incoming light has always been parallel?

Ray diagram showing parallel light entering the eye
Every ray diagram of the eye in this course so far has had parallel light entering the eye.

Why is that?

The answer is because we have always assumed that the eye was at least 6 meters (20 feet) away from the object producing the light. 

So…

Q: What happens when the eye is closer than 6 metres (20 feet) away from the object it’s looking it?

A: The light rays entering the eye will be diverging (not parallel)

We are now going to study 3 diagrams that illustrate the effect of distance (between the object and the eye) on the vergence of light entering the eye and focal distance. 

*Note: These are all emmetropic eyes i.e., not nearsighted, farsighted and no astigmatism.

  1. This first eye is looking at an object situated over 6 meters (20 feet) away – hence the light reaching the eye is parallel.
  2. This results in the focal point forming on the retina.
  3. This means vision is clear
Eye looking at Distance Object
The eye looking at a distant object.
  1. This second eye is looking at an object that is less than 6 meters (20 feet) away – hence the light reaching the eye is divergent.
  2. This results in the focal point forming behind the retina.
  3. This means the vision is blurry.
Eye Looking at Near Object
The eye looking at a near object.
  1. This third eye is looking at an object the very close to the eye – hence the light reaching the eye is very divergent.
  2. This results in the focal point being formed even further behind the retina.
  3. This means the vision is very blurry.
Eye Looking at Very Near Object
The eye looking at a very near object.

Wait… What?

Am I trying to say that anytime we look at something up close the vision is blurry?!

If you are an emmetrope (you don’t wear glasses), you know that’s not true. You can see well in the distance just as well as you can see up close, right? But how can that be if these diagrams are accurate?

Because the crystalline lens is flexible and automatically adjusts its power depending on where you are looking!

This is called accommodation

Yes, let that sink in…

Mind Blown

So check it out;

When looking into the distance, the image already falls on the retina, so the crystalline lens can just relax. In this state, it is said to be at rest. 

The Crystalline Lens at Rest

When looking up close, the crystalline lens ‘knows’ that the light entering the eye is divergent, so it becomes more curved in order to increase they eye’s converging power (to offset the incoming diverging light). This keeps the focal point on the retina and the eye sees clearly. 

The Crystalline Lens Medium Curvature

When looking really close, the light entering the eye is very divergent, so the lens becomes extremely curved in order to compensate. Again, by doing so, the focal point remains on the retina and the eye sees clearly. 

The Crystalline Lens With High Curvature

When the eye is finished looking up close and switches back to looking into the distance, the crystalline lens goes back to being at rest (which means it gets flatter again). 

Accommodation

The constant adjustments that the cyrstalline lens makes in order to keep the vision clear is called accommodation. 

Speed of Accommodation

Accommodation is very fast. So fast in fact that we’re not even aware that it’s happening. When we change the distance at which we are looking, the cyrstalline lens accommodates to that distance before we have time to notice any blur in the vision. 

What Controls Accommodation

Accommodation is all controlled by a muscle that surrounds and suspend the lens in place. This muscle is called the ciliary muscle.

Here is a more in-depth explanation of the mechanism that controls accommodation:

Limits of Accommodation

Accommodation has it’s limits. Generally speaking, the limit is based on age. As we get older, our ability to accommodate gets worse. You can test the limit of your accommodation right now by looking into your palm and moving it closer to your eyes until it becomes blurry. The distance at which you are no longer able to see the details on your palm clearly is the limit of your accommodation. 

If you were to measure and record this limit every year, you would find that it gets further and further out every year.

Eventually, accommodation runs out. But more about that in the next lesson!

==> THE OPTICS OF VISION – PART 10: PRESBYOPIA <== 

Astigmatism Explained

The Optics of Vision – Lesson 8: Astigmatism

After studying this lesson, you will understand a concept that eludes the vast majority of people – Astigmatism! But before you proceed, keep in mind that this is Lesson 8 of the course and it is highly advisable that you have read lessons 1-7 before tackling this one.

Astigmatism

What is Astigmatism?

Astigmatism is a refractive condition that results in the creation of 2 separate focal points.

Recall from Lesson 6 & Lesson 7 that the difference between emmetropia, myopia and hyperopia is where the focal point forms inside the eye.

  • In emmetropia the focal point forms on the retina
  • In myopia the focal point forms in front of the retina
  • In hyperopia the focal point forms behind the retina

In all 3 of these conditions the eye produces only a single focal point. But what if there were 2 focal points…? Then that would be astigmatism!

How Can There Be 2 Focal Points?

Brilliant question!

Everything that you have learned in this course so far suggests that it is impossible for a lens to produce two focal points.

One Lens One Focal Point

Question: So how can one lens produce two different focal points?

Answer: It must have two different curvatures!

Up until now we have always assumed that the lenses and the cornea in our examples have only one curvature, but this is not always true. A lens can have two different curvatures.

Spherical Vs Spherocylindrical Lenses

A lens that has two different curvatures is called a spherocylindrical lens. Before we delve into spherocylindrical lenses, let’s make sure we understand simple spherical lenses.

Spherical Lens

A spherical lens is simply a lens that has the same curvature all around. This is the type of lens we’ve been dealing with in all of our lessons so far.

In the following diagram, you will see a +2.00D spherical lens from two different perspectives. The top is the side view you’re familiar with, but the bottom is an approximately 45° angle view. That’s why it appears oval in nature, but keep in mind that it is the same lens.

Two Perspectives of a Spherical Lens

There’s a lot going on in this diagram so let’s examine it closely.

Notice that:

  • Both top and bottom lenses have the same power; +2.00D
  • Both top and bottom lenses have the same focal distance; 50 cm
  • In a side view (top) only one curvature can be seen; the vertical curvature
  • In a 45° angle view, two curvatures can be seen; the vertical curvature (purple) and the horizontal curvature (green)

In this diagram, we see a lens with a vertical and horizontal curvature that are the same. That’s what makes this a spherical lens.

A spherical lens has the same vertical and horizontal curvature

Note: Just because the horizontal view (top) shows a lens that appears to only have a vertical curvature, it does not mean that it has no horizontal curvature. The horizontal curvature is just not visible from that perspective. When drawn this way, the horizontal curvature is simply assumed to be the same as the vertical curvature.

Now let’s see what happens when the vertical and horizontal curvatures are not the same.

Spherocylindrical Lens

A spherocylindrical lens is different from a spherical lens in that:

  • They have two different curvatures
  • The different curvatures are always 90° apart
  • Each curvatures creates a separate focal point

The following diagram illustrates a spherocylindrical lens.

Spherocylindrical Lens

Notice that this lens has two different curvatures instead of just one. The vertical curvature (purple) corresponds to a +2.00D lens power and the horizontal curvature (green) corresponds to a +5.00D lens power.

When light passes through this spherocylindrical lens, each curve will receive exactly half of the light rays.

  • The rays that pass through the +2.00D curve get focused at 50cm from the lens
  • The rays that pass through the +5.00D curve get focused at 20cm from the lens

The Cornea As A Lens

Remember that the cornea acts as a lens for the eye – and yes – it can either be spherical or spherocylindrical lens!

  • If the cornea is spherical – the eye has no astigmatism
  • If the cornea is spherocylindrical – the eye has astigmatism

First, let’s look at a spherical cornea. Remember, this means there is no astigmatism.

spherical cornea

The cornea is the blue circle. It appears oval because again, we are looking at a 45° angle. If we looked at it straight on it would be a perfect circle.

This cornea has the same curvature in both directions. This makes it a spherical cornea. That’s why it only produces one focal point inside the eye.

Now let’s look at a shperocylindrical cornea.

spherocylindrical cornea

Because this cornea has two different curvatures, it creates two separate focal points inside the eye. That is astigmatism.

What Does Astigmatism Mean For You?

If you have astigmatism, it means that the glasses or contact lenses that you wear will have to correct (with spherocylindrical lenses) for both curvatures of the cornea so that there is only one focal point inside your eye. Remember from Lesson 5 that for an eye to see clearly, there must only be only one focal point and it has to form on the retina. If there are two focal points inside the eye, the eye will not see clearly.

Glasses for astigmatism are no different than glasses that are not for astigmatism. On the other hand, contact lenses for astigmatism are specialized contact lenses that are more expensive and may be more difficult to wear successfully.

Summary

Astigmatism is not an easy concept to grasp. This is a lesson I highly recommend reading a few times as it is quite complex. If you still have questions I would be happy to answer them for you, just let me know in the comments below!

If you’re comfortable with this lesson, congratulations! You now possess knowledge that very few people possess, so use it wisely! You’ll certainly find that it will come in handy if you work in an eye doctor’s office or an optical store.

In the next lesson we’re going to learn about a new part of the eye and how it affects vision. It’s called the crystalline lens. See you there!

==>THE OPTICS OF VISION – LESSON 9: THE CRYSTALLINE LENS <==

Hyperopia featured image

The Optics of Vision – Lesson 7: Hyperopia

This is lesson 7 in this course. Please review lessons 1-6 if you haven’t already done so.

Hyperopia

What is Hyperopia?

Hyperopia, or hypermetropia, is the refractive condition that results when the focal point of parallel light entering the eye forms behind the retina.

The word hyperopia is the name of the condition and the word hyperopia is used to describe somebody with hyperopia. I.e., She has hyperopia, she is hyperopic.

A more common word for hyperopia is farsightedness. The word farsightedness is the name of the condition and farsighted is used to describe someone who has farsightedness. I.e., He has farsightedness, he is farsighted.

Here’s what hyperopia looks like in a ray diagram:

Ray Diagram of Hyperopia

The above diagram decpicts a cross section of an eye with the focal point forming behind the retina. This is just a helpful way of visualizing hyperopia, but in reality, the focal point never actually has a change to form. The light rays are acutally stopped an absored as soon as they hit the retina.

The point is that the light rays are not in focus when the hit the retina, and should they have been able to keep going, the focal point would eventually have formed behind the retina.

Just like in myopia, hyperopia exists in varying degrees of severity. It can be very low or very strong as you can see here:

3 Different Stages of Hyperopia

The reason for the focal point forming behind the retina in hyperopia is that the cornea does not converge the light entering the eye enough.

Recall from Lesson 3 that lens power and the focal distance are linked in the following way:

The higher the lens power, the shorter the focal distance.

The lower the lens power, the longer the focal distance.

In the case of hyperopia, the focal distance is too long. To shorten the focal distance, we have increase the lens power.

How do we increase the lens power of the cornea? Well we cann change the shape of the cornea itself, so we have to add lenses in front of it.

Recall from Lesson 5 that the cornea acts as a plus (converging) lens. Theefore, in order to increase the overall power of the eye, we will have to add more plus (convering) lenses in front.

*Note that to correct hyperopia, we are doing the exact opposite as what we do to correct myopia.

To illustrate how adding plus (converging) lenses in front of an eye helps correct hyperopia, let’s consider the following example.

Ray Diagram of Hyperopia with Figures

In this example, we see parallel light coming from optical infinity, we see that the cornea has a power of +0.50D, the length of the eye is 1.8cm (0.018m) and the focal point is 0.2cm (0.002m) behind the retina.

The question is; what lens power needs to be placed in front of the eye in order for the focal point to land exactly on the retina.

Ray Diagram of Hyperopia Corrected by Mystery Plus Lens

Let’s start by establishing the goal. The goal is to have the focal point on the retina. The retina is 1.8cm behind to the cornea. So what total lens power do we need for that?

The formula for lens power is:

lens power = 1 / focal distance

In this example we want the focal distance to be 1.8cm (because that’s how far the retina is from the cornea).

lens power = 1 / 0.018

lens power = +55.5D

This means that for the focal point to be on the retina, the cornea must have a lens power of +55.5D. But it only has a lens power of +50D, not +55.5D, so what do we do?

Well, since the cornea is missing +5.5D of converging power, we will add an plus (converging) lens in front of the cornea with a power of +5.5D!

Calculations

Total Power Needed = Power of the Cornea + Power of Glasses Needed

+55.5D = +50D + Power of Glasses Needed

Power of Glasses Needed = +55.5D – (+50D)

Power of Glasses Needed = +5.5D

Ray Diagram of an Emmetropic Eye With CorrectiRay Diagram of an Emmetropic Eye With Corrective Lensve Lens

So in this example, with a +5.5D plus lens in front of this eye, the light is perfectly focused on retina!

Just like in our example from Lesson 6, this is not exactly how optometrists figure out what lenses will make the vision better. They don’t know what the length of the eye is so these calculations are not possible in the exam room. Instead, they just test different powered lenses in front of the patient’s eyes until they find the one which gives the best vision (… in a nutshell).

Pop Quiz!

Ok, now that we have a better undesrstanding of hyperopia, try to answer this question based on everything you know so far.

Why do farsighted people (people with hyperopia) have more difficulty seeing up close than in the distance?

Hint: Think of how light behaves when it comes from a distance vs when it comes from up close.

Leave comment below to find out the answer!

We have now learned a lot of theory in this course. If you have any questions about any of the material so far it’s very important that you clear it up before the next lesson. You can leave your questions in the comments section of any of the lessons.

The reason I bring this up is because the next lesson will really test your understand of the concepts we’ve learned so far. It’s one of the most difficult refractive conditions to grasp and the vast majority of people have no idea what it is. I’m talking about astigmatism. So get prepared, and then move onto Lesson 8!

==>The Optics of Vision – Lesson 8: ASTIGMATISM <==

Lens Power - Featured Image

The Optics of Vision – Lesson 3: Lens Power

Now that we understand light and lenses, we will be learning about how to quantify the effect that lenses have on light. This is the concept of lens power and it will put us well on our way to understand vision and glasses work.

To understand the concepts covered in this lesson, it is best to have read:

Now let’s begin!

Lens Power

What is Lens Power?

The power of a lens is also often referred to as the strength of a lens. It refers to how much of an effect a lens has on light passing through it.

A lens with high power has a big effect on the path of light passing through it and a lens with low power has a small effect.

What Determines Lens Power?

The main determinant of lens power is the curvature of the lens.

The more curved a lens’ surface is, the more power it has and the more it will change the direction of light.

Insert Image

What Types of Lens Powers Are There?

Recall from Lesson 2 that lenses can either be converging (+) or diverging (-).

  1. Converging lenses have converging or plus power 
  2. Diverging lenses have diverging or minus power

Plus Power

The following diagram will illustrate the concept of plus power.

It shows 3 different converging lenses, each with a different curvature.

The most curved lens has the most power and changes the direction of light the most.

The least curved (flattest) lens has the least power and changes the direction of light the least.

Convex lenses Different powers - Curves

Minus Power

The next diagram will illustrate the concept of minus power.

It shows 3 different diverging lenses, each with a different curvature.

Again, the most curved lens has the most power and changes the direction of light the most.

The least curved (flattest) lens has the least power and changes the direction of light the least.

Concave Lenses Different Curves

Can you see that in both diagrams, the most curved lens ‘bends’ the light rays the most and the least curved lens ‘bends’ them the least? That is the result of each lens having a different power/strength, which is based on the curvature of the lens.

Now, in the real world, we need a way of describing the exact curvatures of lenses. We can’t just say ‘high curve’, ‘moderate curve’, or ‘low curve’ to describe lenses. That is not accurate enough.

Next, we will learn exactly how lens power is measured and quantified.

How is Lens Power Measured?

It has to do with something called the focal distance of the lens. Let’s learn more about focal distance before we delve into lens power.

Focal Distance of a Plus Lens

Recall from Lesson 1 that converging light eventually forms something called a focal point.

ray diagram of converging light, focal point, and diverging light
Figure from Lesson 1

We’ve also learned from Lesson 2 that plus lenses cause incoming parallel light to become converging.

Ray diagram of parallel light passing through a convex lens
Figure from Lesson 2

So if plus lenses cause light to converge and converging light forms a focal point, then every plus lens will create a focal point.

Let’s re-examine the following diagram. This time, note how the focal point for each lens is formed at different distances from the lenses themselves.

Convex lenses Different powers - Focal Point

The distance from the lens to the focal point is called the focal distance.

Focal Distance of a Minus Lens

Just like plus lenses, minus lenses also form focal points. There’s just a small difference.

Remember that minus lenses cause light to diverge, meaning that once the light passes through a minus lens, the light rays move further and further apart from each other.

Now at this point, you may be wondering… If a focal point happens when all the light rays come together, then how can diverging light ever come to a focal point? That’s a great question!

In fact, the focal point doesn’t happen after the light passes through the lens, it happens before.

To find where the focal point is on a minus lens, you have to extend each of the light rays exiting the lens backward until they all meet.

The Focal Point of a Concave Lens

We can do this with any minus lens. Let’s see what it looks like with our 3 minus lenses from earlier. Also note here that distance between the focal point and the lens increases as the lens gets flatter, just as it did with plus lenses.

Concave Lenses Different Powers With Focal Point and Distance

Again, just as with plus lenses, the distance between the focal point and the lens is called the focal distance.

Calculating Lens Power From Focal Distance

The power of any lens is based on its focal distance. To be more precise, the power of a plus lens is the inverse of its focal distance.

The power of a lens is the inverse of its focal distance.

What does this mean? Don’t worry, it’s not difficult!

In mathematical terms, the inverse of ‘something’ means dividing 1 by that ‘something’.

In this case, I said that the power of a plus lens is the inverse of its focal distance. The inverse of the focal distance means 1 divided by the focal distance. Therefore, lens power = 1 / focal distance.

Lens Power = 1 / Focal Distance

See, simple right?

Now there’s just one last thing to remember. When calculating lens power, we must use meters when measuring the focal distance. This produces a unit called Diopters, and that’s what lens power is measured in!

This will make a lot of sense when we start looking at examples.

We’re going to use the same diagrams as before but now we will assign some values to the focal distance so we can calculate the lens power.

Calculating Plus Lens Power

Convex lenses Different powers - Focal Distances

Let’s calculate the lens power of each lens in the diagram.


Top Lens

Example of a plus 5D lens small

The focal length is 0.20m.

The equation we’re using is:

Lens Power = 1 / Focal Length

The Calculation is:

Lens Power = 1 / 0.20m = +5D


Middle Lens

Example of a plus 2D lens smallThe focal length is 0.50m.

The equation we’re using is:

Lens Power = 1 / Focal Length

The Calculation is:

Lens Power = 1 / 0.50m = +2D


Bottom Lens

Example of a plus 1D lens smallThe focal length is 1m.

The equation we’re using is:

Lens Power = 1 / Focal Length

The Calculation is:

Lens Power = 1 / 1m = +1D


That was easy right?

Let me just point out 2 things before we move onto minus lenses.

  1. No conversions were necessary because all values were already in meters. If I had given the values 20cm, 50cm and 100cm, we would have had to convert them to meters before we did the calculations.
  2. Because we were calculating the power of a plus lens, by convention we must include a plus sign in front of the lens power.

Calculating Minus Lens Power

Calculating the power of minus lenses may seem more complicated, but it’s the exact same steps.


Top Lens

Minus 8 diopter concave lens

The focal length is 0.125m.

The equation we’re using is:

Lens Power = 1 / Focal Length

The Calculation is:

Lens Power = 1 / 0.125m = -8D


Middle Lens

Minus 3 diopter concave lens

The focal length is 0.333m.

The equation we’re using is:

Lens Power = 1 / Focal Length

The Calculation is:

Lens Power = 1 / 0.333m = -3D


Bottom Lens

Minus 1 and half diopter concave lens

The focal length is 0.666m.

The equation we’re using is:

Lens Power = 1 / Focal Length

The Calculation is:

Lens Power = 1 / 0.666m = -1.5D


Again, keep in mind these 2 things when calculating lens power.

  1. No conversions were necessary for the examples above because all values were already in meters. If I had given the values 12.5cm, 33.3cm and 66.6cm, we would have had to convert them to meters before we did the calculations.
  2. Because we were calculating the power of minus lenses, by convention we must include a minus sign in front of the lens power.

Key Points to Remember:

  • Every lens (plus or minus) has a focal point
  • The distance between the focal point and the lens is called the focal distance
  • The formula for lens power is the same for plus or minus lenses:

Lens Power = 1 / Focal Distance

  • The power of plus lenses are always denoted with a + (plus sign)
  • The power of minus lenses are always denoted with a – (plus sign)

This lesson may take a few reads to really set in. If you still have questions about the material, feel free to leave them in the comments section and I will post some additional clarifications for you.

Great job making it this far into the course! This may be a good time to review Lessons 1,2 & 3 because in Lesson 4 we will switch gears and start learning about eye anatomy!

==> The Optics of Vision – Lesson 4: Introduction to Eye Anatomy <==